- 0
- 호샤
- 조회 수 2658
알람 내역 :
ALARM TEXT
X LIMIT EMG. STOP. -> M.RST.
Z LIMIT EMG. STOP. -> M.RST.
Y LIMIT EMG. STOP. -> M.RST.
OP. PANEL EMG. HAS BEEN PUSHED.
MAG.PANEL EMG. HAS BEEN PUSHED.
EMG. EXPAND MODULE WD. ERR.
O.T. RELEASE RLY WD. ERROR.
MACHINE START-UP RLY WD. ERR.
PLS SET HARDWARE TYPE IN K9
MAG. POCKET NO.(D20) > 60
NO CONFIRM. OF SPDL HEAD COVER
POWER OFF -> POWER ON.
XP IS SELECTED !!
NO CONFIRM. OF POT UP.
NO CONFIRM. OF POT DOWN.
POT UP & DOWN BOTH ON.
NO CONFIRM. OF TOOL CLAMP.
NO CONFIRM. OF TOOL UNCLAMP.
TOOL CLAMP/UNCLAMP LS. BOTH ON.
MAG. NOT INPOSITION.
MAG. ROTATE TIME OUT.
ATLM CIRCUIT CHECK ERROR.
DURING T CYCLE,POWER DROP DOWN.
DURING M6 CYCLE,POWER DROP DOWN.
ILLEAGL T-CMD, T-CMD > MAX.T-NO.
SPDL NOT ORIENT.
AXES NOT AT ATC POS.
ARM SEN. DETECT ERR. PLS CHK. CIRCUIT.
TL-TAB. SET ERR. PLS CHECK.
ATC TEMP STOP,CONTINUE->C-START.
THE TOOL IS NOT REGISTERED.
NO FREE POCKET FOR SPDL TOOL
CLR TASK BY "RST+FEED HD"=>2SEC.
TOOL NO ARE DUPLICATE.
SP.TL-NO(D0)&TYPE(D50) NOT MATCH.
ARM1 & 2 DATA ERR. CHK D6 & D8.
ARM NOT AT 0D POS.
NO T CMD. & PERFORM M6
NO CONFIRM. OF 4th
AXIS CLAMP.
NO CONFIRM. OF 4th AXIS UNCLAMP.
4th AXIS CLAMP/UNCLAMP BOTH ON.
4th NOT AT UCMP POS. M11=>4th UCMP.
Z-BRK CTRL. RLY WD. ERROR.
NO CONFIRM. OF WK-PIECE CLAMP.
NO CONFIRM. OF WK-PIECE UNCLAMP.
WK-PIECE CLAMP/UNCLAMP BOTH ON.
NO CONFIRM. OF 5th AXIS CLAMP.
NO CONFIRM. OF 5th AXIS UNCLAMP.
5th AXIS CLAMP/UNCLAMP BOTH ON.
5th NOT AT UCMP POS. M46=>5th UCMP.
U+OT, PRESS OT REL. PB TO RELEASE
U-OT, PRESS OT REL. PB TO RELEASE
SCREW AUGER MOTOR OL.
CHIP CONVEYOR MOTOR O.L.
WASH DOWN PUMP OL.
CTS. PUMP O.L.
NOZZLE PUMP O.L.
OIL SKIMMER MOTOR OL
OIL CHILLER OL
OIL CHILLER ALARM
ATC-MAG. MOTOR OL.
ATC-ARM MOTOR OL.
THIS GROUP->ALL TL LIFT IS OVER.
RUN SP TL CLAMP BEFORE ARM SRV
RUN SP TL UNCLAMP BEFORE ARM SRV
SRV KEY -> ARM CCW TO 0D.
SRV KEY -> SPDL ORIENT.
SRV KEY -> SPDL TOOL CLAMP.
SRV KEY -> SPDL TOOL UNCLAMP.
SRV KEY -> ARM CW TO BOTTOM POS.
SRV KEY -> ARM CCW TO BOTTOM POS.
C-ST.-> SRV FIN. & AUTO CONTINUE.
C-ST.-> CONTINUE ATC CYCLE.
POCKET NO.(D20) HAS BEEN CHANGE.
PERFORM TOOL-TABLE REGULATE.
NOW => SPDL AT CLAMP POS.
NOW => SPDL AT UNCLAMP POS.
NOW => ATC-ARM AT 60D
NOW => ATC-ARM AT BOTTOM
NOW => ATC-ARM AT 0D
NOW => ATC-ARM NOT INPOS.
FRONT DOOR WAS OPENED.
알람 처리 방법 및 조치사항 :
아래 자료 받아 주세요
알람 처리 방법 자세히 나와 있습니다.
VMV's XP3/화낙콘트롤러 18iMB의 PLC 알람 리스트 조치방법
P3/화낙콘트롤러 0iMC의 PLC 알람 리스트
공유
